一台JS型铜笼条转子电动机堵转电流不平衡又偏小分析检查着重对转子铁心和笼条检查，发现有三个槽的铜笼条离铁心端45mm处断裂，其中三根全断开，一根尚有1mm厚相连。细看断裂的4 根为Φ10mm黄铜棒，为上次断条故障时更换的，其余均为原配Φ10mm紫铜棒。分析原因是电动机转子不平衡振动大，新换黄铜棒材质不佳，焊接不良，才导致二次断条。

1000kW电机维修修理方法：

通过调整潜水电动机窜动量及轴向尺寸的积累误差，用以纠正开关装配尺寸误差，调整后起动有好转，但仍不理想，检查发现开关转速整定值取的偏低，经适当调整和整定后，起动故障没有了。

　三相电动机起动困难修理实例3、4某化工厂用185kw 西玛电动机增大起动转矩解决起动困难的做法问题分析三相异步电动机为了降压起动，通常采用丫联结起动，△ 联结运行。该机驱动的化工机械惯性大，起动时要求有较大转矩，运行中要求转矩较小，运行时电流为额定值的1/3~ 1/6 。换小容量电动机又满足不了起动要求。结果采取改变起动和运行时绕组联结方式，既克服了起动困难，又节约了电能。

　修理方法因该机引出6 根引线，丫形联结时，三根末端引线在外部封成星点。只要先剥去星点外绝缘层，用电烙铁烫开星点，把三相首末引线相序找对后，再按△ 形联结接好线，焊牢和包上绝缘，就把接错线的毛病纠正。

1000kW电机维修价格，前进水泥助磨剂有限公司为您提供生料烘干风扫磨技术改造、煤磨动态选粉机。生料烘干风扫磨技术改造，煤磨动态选粉机高效动态立式烘干机的关键技术是使物料能在烘干机内尽可能分散，以提高热烟气与物料接触面积，同时控制物料在烘干机各区域流速和停留时间，使热烟气与物料充分对流、辐射、传导换热。

采用物料烘干参数优化微机软件技术，对预热带、烘干带、干燥带三个区域的物料水份和气体温度进行在线检测，并对系统的供热能力、引风量、二次热风分布及供热能力、物料截流量及停留时间等系统参数进行在线调整，实现系统的动态优化平衡，提高系统热能利用率。高效动态立式烘干机主要由固定筒体、进出风装置、进出料装置、热交换装置、保温装置等构成。本产品所采用的动态立式烘干技术能使物料在烘干机内尽可能分散以提高热烟气与物料接触的面积，使热烟气与物料充分对流、辐射、传导换热。结构创新点运用高效立式烘干机的烘干原理和方法，同时。

　为重点工程配套的产品，愿意接收用户监造。在交付产品时，根据用户要求，派出技术服务人员参加开箱验收，指导产品安装调试，直到产品正常运转。